Keenetic start does not connect to the Internet. Wi-Fi router Zyxel Keenetic Start II - Reviews

The next step is to connect the router ZYXEL Keenetic Start II to a laptop or personal computer(PC). To do this, you need to connect the cable that the provider has installed to the "INTERNET" port of the router (this is the cable that goes to the apartment, house, office, etc. from outside). The cable that came with the router, connect one end to the router's "HOME NETWORK" port, and connect the other end to a laptop or PC. And yes, do not forget to connect the power cable.

If you have network problems when connecting, go here to solve it:

ZYXEL Keenetic Start II router authorization

So, we connected the router, now you need to use any browser (be it Google Chrome Mozilla Firefox, Internet Explorer, etc.) get into its web interface. To do this, open the browser and in the address bar we drive in the address of the router: my.keenetic.net or 192.168.1.1 and press the button " Enter" on keyboard.

After, the router offers us to make a quick setup, select the interface language - "Russian" and click the Web configurator.


After that, the router can display a window for setting a password on the web interface. Here, if you wish, you can set a password, you can not. If you set a password, write it down somewhere.


Also, ZYXEL routers operate in different modes, it will not be superfluous to check whether the mode is selected. Click on the shortcut in the bottom menu System"and go to the tab" Mode". If you are setting up the Internet with a login and password, leave the mode" Internet center - basic mode".


Configuring the ZYXEL Keenetic Start II router

Now you need to configure the router. First of all, we will secure the wireless network by setting a password for wi-fi. Then you will need to find out what type of connection is used to access the Internet, is it PPTP, L2TP or PPPOE. You can find out by calling the provider (this is the organization with which you have concluded an agreement to provide Internet services). So, let's start setting up the router.

Setting a password for wi-fi

I offer Video instructions for setting a password for wi-fi on a router ZYXEL Keenetic Start II on the example of the ZYXEL Keenetic Start II router.

Let's also take a written and illustrative look at setting a password for wi-fi on a router ZYXEL Keenetic Start II in two frequencies.
1. Click on the Web interface in the bottom menu on the shortcut " WiFi network", get into the network settings" 2.4 GHz hotspot".
2. Check if the checkbox is checked Enable hotspot", then in the field " Network name (SSID)"come up with a name wireless network, this name will continue to glow when you connect to the network.
3. "Network protection" - WPA2-PSK.
4. Now you need to set a password for the wireless network. In field " Network Key"Create and type in a password.
5. "Channel Width" - "20 MHz".
6. Press " Apply".


PPTP setup

PPTP on the router ZYXEL Keenetic Start II

PPTP on the router ZYXEL Keenetic Start II.
1. Internet".
2. Select the tab " PPPoE/VPN"press" Add connection".


3. Turn on" And "".
4. IN " DescriptionType (protocol)"choose" PPTP", "Connect via"choose" Broadband connection (ISP)".
5. Username"), password (on the line " PasswordServer address
6. "Configuring IP Settings" - "Automatic".
7. Apply".


Setting up PPTP with a static IP address

PPTP with static IP on the router ZYXEL Keenetic Start II
1. Click on the shortcut in the bottom menu Internet".
2. Select the tab " PPPoE/VPN"press" Add connection".


3. In the window that appears, check the checkboxes next to " Turn on" And " Use to access the Internet".
4. IN " Description" enter any word in Latin, for example "Host", " Type (protocol)"choose" PPTP", "Connect via"choose" Broadband connection (ISP)".
5. Below you are prompted to specify the username (in the line " Username"), password (on the line " Password"). You will also need to specify the ip-address of the server (in the line " Server address").
6. Manual" against " Configuring IP Settings".
7. Specify ip-addresses and DNS.
All this data is usually prescribed in the contract with the provider. If for some reason they could not find them, you need to call the provider's hotline and find out how you can get them.
7. Once you have entered all the required information, click the " Apply".


Setting L2TP

I offer Video instructions for setting up the connection type L2TP on the router ZYXEL Keenetic Start II on the example of the ZYXEL Keenetic Omni II router.

Let's also take a written and illustrative look at the connection setup L2TP on the router ZYXEL Keenetic Start II.
1. Click on the shortcut in the bottom menu Internet".
2. Select the tab " PPPoE/VPN"press" Add connection".


3. In the window that appears, check the checkboxes next to " Turn on" And " Use to access the Internet".
4. IN " Description" enter any word in Latin, for example "Host", " Type (protocol)"choose" L2TP", "Connect via"choose" Broadband connection (ISP)".
5. Below you are prompted to specify the username (in the line " Username"), password (on the line " Password"). You will also need to specify the ip-address of the server (in the line " Server address"). All of the above data is provided by the provider (the organization that conducted the Internet).
All this data is usually prescribed in the contract with the provider. If for some reason they could not find them, you need to call the provider's hotline and find out how you can get them.
6. "Configuring IP Settings" - "Automatic".
7. Once you have entered all the required information, click the " Apply".


Setting up L2TP with a static IP address

Consider connection setup L2TP with static IP on the router ZYXEL Keenetic Start II. Usually a static IP address is provided legal entities, either as additional service to the basic tariff for individuals.
1. Click on the shortcut in the bottom menu Internet".
2. Select the tab " PPPoE/VPN"press" Add connection".


3. In the window that appears, check the checkboxes next to " Turn on" And " Use to access the Internet".
4. IN " Description" enter any word in Latin, for example "Host", " Type (protocol)"choose" L2TP", "Connect via"choose" Broadband connection (ISP)".
5. Below you are prompted to specify the username (in the line " Username"), password (on the line " Password"). You will also need to specify the ip-address of the server (in the line " Server address").
6. Since the connection uses a static IP address, select " Manual" against " Configuring IP Settings".
7. Specify ip-addresses and DNS.
All of the above data is provided by the provider (the organization that conducted the Internet).
All this data is usually prescribed in the contract with the provider. If for some reason they could not find them, you need to call the provider's hotline and find out how you can get them.
7. Once you have entered all the required information, click the " Apply".


PPPOE setup

I offer Video instructions for setting up the connection type PPPOE on the router ZYXEL Keenetic Start II on the example of the ZYXEL Keenetic Omni II router.

Let's also take a written and illustrative look at the connection setup PPPOE on the router ZYXEL Keenetic Start II.
1. Click on the shortcut in the bottom menu Internet".
2. Select the tab " PPPoE/VPN"press" Add connection".


3. In the window that appears, check the checkboxes next to " Turn on" And " Use to access the Internet".
4. IN " Description" enter any word in Latin, for example "Host", " Type (protocol)"choose" PPPOE", "Connect via"choose" Broadband connection (ISP)".
5. Below you are prompted to specify the username (in the line " Username"), password (on the line " Password"). All of the above data is provided by the provider (the organization that conducted the Internet).
All this data is usually prescribed in the contract with the provider. If for some reason they could not find them, you need to call the provider's hotline and find out how you can get them.
6. "Configuring IP Settings" - "Automatic".
7. Once you have entered all the required information, click the " Apply".


Setting up PPPOE with a static IP address

Consider connection setup PPPOE with static IP address on the router ZYXEL Keenetic Start II. Typically, a static IP address is provided to legal entities, or as an additional service to the basic tariff for individuals.
1. Click on the shortcut in the bottom menu Internet".
2. Select the tab " PPPoE/VPN"press" Add connection".


3. In the window that appears, check the checkboxes next to " Turn on" And " Use to access the Internet".
4. IN " Description" enter any word in Latin, for example "Host", " Type (protocol)"choose" PPPOE", "Connect via"choose" Broadband connection (ISP)".
5. Below you are prompted to specify the username (in the line " Username"), password (on the line " Password").
6. Since the connection uses a static IP address, select " Manual" against " Configuring IP Settings".
7. Specify ip-addresses and DNS.
All of the above data is provided by the provider (the organization that conducted the Internet).
All this data is usually prescribed in the contract with the provider. If for some reason they could not find them, you need to call the provider's hotline and find out how you can get them.
7. Once you have entered all the required information, click the " Apply

In this manual, we will look at connecting and configuring a budget ZyXEL Keenetic Start router. ZyXEL routers have Russified simple and clear interface, and are also equipped detailed instruction in Russian. Therefore, their configuration will not cause difficulties even for novice users.

How to connect a ZyXEL Keenetic Start router

The router has a standard interface similar to devices from other manufacturers. On the back panel there is a blue WAN port for connecting to the Internet, four LAN ports, a power supply connector, power and reset buttons.

We connect the cable coming from the Internet provider or ADSL modem to the WAN port. We connect one of the LAN ports with a yellow patch cord, which is included in the delivery package of the router, to the network card of your PC. We connect the power supply cord, and the unit itself - to the 220V network. Turn on the router with the button on the back panel. The indicators on its front panel should light up.

Indication

On the front panel of the ZyXEL Keenetic Start are LED indicators that allow you to control the operation of the router.

  • The Power indicator shows that the power is on
  • Port LEDs 0 to 4 show port activity. 0 is WAN port, 1-4 are LAN ports
  • The Wi-Fi indicator is responsible for the activity of the wireless network
  • Internet connection indicator in the form of a globe shows whether there is a connection to the network at the moment
  • The last indicator shows whether any device is currently connected to the USB port of the router, if such a port is present in your model

When you turn on the router, at least the indicators for the power, WAN port, and one of the LAN ports should light up. If none of the lights are on, check if the power button on the back of your device is disabled. If the indicators are on, you can proceed to the setting.

How to set up a router

The ZyXEL Keenetic Start router is configured through the device's web interface. To enter it, you will need those indicated on the label pasted on the bottom.

For ZyXEL routers, the web interface access address looks like 192.168.1.1 or my.keenetic.net. Enter this address in the line of your browser and press Enter. The panel login window should appear. The default login and password is admin/admin.

If your ISP is configured to bind the connection to the MAC address, then the configuration must be carried out from the computer on which the Internet was previously connected and configured.

Quick Setup

In the latest firmware versions, there is a "NetFriend Quick Setup" button in the upper right corner. If it is present in your firmware, you can use it to start the wizard quick setup. It will guide you step by step to set up your internet connection.

In the first window, you will need to enter the MAC address, if required by your ISP. The MAC of your PC, to which the Internet is tied, can be found by typing in command line ipconfig /all. In the output, we are looking for "Ethernet Ethernet Adapter", in the line "Physical Address" the MAC address we need is displayed.

Next, sequentially enter the IP address, if necessary, as well as the username and password. These parameters must be provided to you by your ISP. After completing all the steps, the router will show all the settings you entered. Check them and, if all the parameters are correct, click on the "Web configurator" button. The setup wizard will apply the new settings and offer to replace the standard password for accessing the device web interface with a new one. This is worth doing for security reasons.

Router setup is complete.

Manual setting

If your firmware does not have a quick setup wizard or if you need to change some settings, you can configure your router manually.

Internet connection

We open the web interface, go to the "Internet connection" item (the second button on the toolbar at the bottom of the page) and get to the "Connection to the Internet and other networks" page. This will list all connections on your device. But if you have not configured anything yet, then this list will contain only one item - “Broadband connection”. It will be marked with a red icon, which means: the connection is not configured. We double-click on it and see the settings window in front of us.

On ZyXEL routers, there is a convenient option - manually assign a WAN port. This can be useful if, for example, a thunderstorm causes the default port to fail. If the port is working, there is no need to change anything.

Below you need to enter the data provided by the provider - MAC, login, password, etc. Then click the "Apply" button. Internet connection is set up. The icon next to it should turn green.

This method works for most providers, however, in some cases, for example, when connecting to the Internet from Beeline or Rostelecom, you will need to configure the settings in a different way.

Setting up PPPoE, L2TP, PPTP

Some providers use PPPoE, L2TP or PPTP protocols to connect to the network. Consider step by step setup such a connection using PPPoE as an example.

On the Internet settings page, which is displayed as a globe, go to the PPPoE / VPN tab and click the "Add connection" button. A settings window will open, in which you need to select the type of connection from the drop-down list. In this case it will be PPPoE.

Below you need to enter your login, password, IP address. All this data must be provided to you by the provider. In the "Connect via" field, select "Broadband connection".

After all the required fields are filled in, click the "Apply" button.

L2TP and PPTP connections are configured in the same way.

If your provider provides a static IP address for connection, which is rare, you need to configure such a connection in the IPoE tab.

WiFi setup

The wireless network on your router works by default, you do not need to configure it additionally. The network name and password (network key) are on the label on the bottom of the machine. It is not necessary to change them. However, if you decide to do this, use the "Wireless Network" button (the fourth on the toolbar at the bottom). On the "Access Point" tab, change the desired settings and save the changes.

If you have already used a router with standard wireless network settings before, then on all devices that use a Wi-Fi connection, you will need to enter a new password.

Some users confuse menu items and try to set up a wireless network on the Internet connection page in the Wi-Fi tab. This is a common mistake. On this tab, settings are made if your router will receive Internet via Wi-Fi from another router or access point.

Setting up IPTV

If IPTV on your device does not work automatically, you also need to configure it. To do this, go to the "Home Network" section (the third button on the bottom toolbar) and on the IGMP proxy tab, check the box next to the "Enable IGMP proxy" item.

This is enough for the IPTV function to start working on your device.

Change access password

In order to change the username and password of the device administrator, you need to perform the following steps.

Go to the "System" page (the penultimate button on the bottom toolbar) and find the "Users" tab there. If you have not created new users, only admin will be listed. Click on it with the mouse. A settings window will open where you can enter a new password and save the changes. Be sure to write down the password so as not to lose access to the device.

Setting up a home network

Your router is already set up to be used as a home network router. All devices connected to it will have access to network resources and connect with each other. You can view the settings of your home network, as well as a list of connected devices, on the page " System Monitor”, tab “Home network”.

If necessary, you can change these settings on the "System" page, "Setup" and "Configuration" tabs.

Troubleshooting

If the router does not work correctly, errors and failures occur regularly, you can track errors in the system message log. It's on the System page.

It will be difficult for an ordinary user without special knowledge to understand these messages, however, information from the log may be required when contacting the provider's technical support service.

In the latest firmware versions, the ability to diagnose problems with the router through the web interface is implemented. If you go to the "Diagnostics" tab on the "System" page and click the "Start Debugging" button, the router will perform advanced self-diagnostics and write data to a file that can be saved to a computer and sent to technical support.

Reset

If some settings have already been made on the router and they were made incorrectly, as a result of which the device does not work correctly, you can return the factory default settings. To do this, we find the "Reset" button on the back panel. It is small and deeply recessed into the body. To press it, you will need some thin object - for example, a paper clip or a needle. We insert the needle into the hole, press the button and hold for 10 seconds. All indicators on the front panel should turn off and then turn on again. The reset has been completed.

You can do the same if you lost or forgot your password, or bought a used router and don't know the password.

Keep in mind that in the event of a factory reset, you will have to reconfigure all settings manually or through the Quick Setup Wizard.

Firmware update

Hardware manufacturers update software for their devices from time to time. It often happens that you have purchased a router with already outdated firmware, and therefore you may not have any necessary functions in the settings.

With the ZyXEL Keenetic Start router, the update process will not cause difficulties and take a minimum of time.

If you are setting up Internet access using the setup wizard and the router will automatically connect to the network without additional parameters (this works for most providers), then at the next step the wizard will offer to install and download updates. You need to confirm your choice by pressing the button and wait a bit. The firmware of your device will be updated and you can continue with the setup.

If the router could not connect to the Internet on its own and you had to perform the settings manually, you can update the firmware in the same way automatically, using a built-in function. To do this, log in to the web interface. You will immediately be taken to the "System" tab, where all the current parameters of your device are displayed.

On the right, in the "System Information" subsection, there is an "Updates" item. Opposite it there will be an active link "Available" if there is a new firmware on the developer's server. Click on this link - the router will download the updates, install them and reboot. As you can see, there is nothing complicated here.

There is a third way to update the firmware, download and install new version from the manufacturer's website. This method is useful if you have an old firmware that does not support updating in automatic mode, or for some reason, the update cannot be performed in this way. Also, this method allows you to flash the device with an alternative modified third-party firmware. However, remember that by installing third-party software, you act at your own peril and risk. The manufacturer's warranty will be void in this case.

The firmware can be downloaded from the ZyXEL official website.

Please note that each router model has several revisions (hardware versions). firmware different versions incompatible. If you try to flash your device with the wrong firmware, it may stop working. Therefore, before downloading software, check the hardware version of your router. It is indicated on the label at the bottom, for example, Rev A or Rev B.

Download the archive with the firmware and unpack it into a separate folder.

It is strongly recommended that you flash this way only through a cable connection. During the flashing process, the wireless network may be temporarily disabled, which will lead to a disconnection between the router and the computer. As a result, the firmware will not be completed to the end and your device may not turn on at all.

Now we go to the web interface of the router. The System page has a Files tab. We open it and see a small list in which we find the firmware. This is the firmware file. We click on it and see a window with two active buttons "Select a file" and "Save" and an inactive "Replace". You can download old version firmware for computer by clicking the "Save" button.

For that, to update the firmware, click the "Select file" button and select the downloaded file of the new firmware. After that, the "Replace" button will become active. Click on it and wait for the process to complete. After the update software completed, the router will reboot.

As you can see, the ZyXEL Keenetic Start router is one of the easiest to set up, so any user can handle this task.

In order to get into the web interface of the router, you need to open your Internet browser and type 192.168.1.1, User Name in the address bar admin (Username), Password (password) - 1234 (provided that the router has factory settings and its IP has not changed).

Change factory password

For security reasons, it is recommended to change the factory password. Default: Login admin, password 1234. In the interface of the router, go to the tab " System", Further password. In field "New password" Enter a new password. It must be repeated in the next field. Next, save the settings by pressing the button " Apply».

Setting up Wi-Fi on the router

Select a section at the bottom of the page WiFi.

  1. In the window that appears in the field Network name (SSID) enter the name of your network (any)
  2. In field Network protection select WPA2-PSK
  3. In field Network Key enter your password to access the network (any)
  4. In field Channel: select Auto
  5. Apply.

Internet connection setup

NAT when automatically obtaining an IP address (DHCP)

Choose a section Internet, then point IPoE and click the Add interface button:

  • use connector- a check mark on the one into which our Internet cable is plugged, in this case the last port
  • Transmit VLAN ID tags- tick the box
  • Enable Interface- so put a tick
  • Description- e.g. internet
  • IP Address and Subnet Mask- leave empty
  • Get address via DHCP- put a tick
  • This direct connection to the Internet- and here we put a tick

Setting up PPTP (VPN) when automatically obtaining a local IP address

Select the tab at the top of the page Authorization.

  1. In field Type (protocol used) select PPTP
  2. In field Connect via select Broadband connection (ISP)
  3. In field Server address enter Server name or address(check with provider)
  4. In field Username enter your login from the contract
  5. In field Password enter your password from the agreement
  6. In field Authentication method select Auto
  7. - may not be filled
  8. After filling in all the fields, click the button Apply.

Setting up a PPPoE connection (Rostelecom, Dom.ru)

InternetAuthorization»

  1. Type (protocol):PPPoE
  2. Username : Your contract login
  3. Password: Your contract password
  4. Setting IP parameters: Automatic
  5. Service Name, Hub Name, Description- may not be filled
  6. In field Authentication method select Auto
  7. Save settings with the button "Apply".

Setting up an L2TP connection (Beeline)

In the router interface, select the tab on the left " Internet”, in the list that opens, select “ Authorization»

  1. Internet Access Protocol: L2TP
  2. Description: connection name
  3. Server address: name or address of the server (specified in the contract)
  4. Username : Your contract login
  5. Password: Your contract password
  6. Authentication method: Auto
  7. Save settings with the button "Apply".

Setting up a Wi-Fi router ZyXEL Keenetic Start

The ZyXEL Keenetic Start router allows you to connect up to 4 devices in an apartment using wired communication lines at speeds up to 100 Mbps, and also provides connection of wireless devices with a wireless data transfer rate of up to 150 Mbps. Consider the necessary settings for this router to work in the Insys network.

1. Connecting the router to the PC on which the configuration is being performed:

Connect the incoming cable "Insys" to the blue port on the router ("INTERNET" port), then you need to connect the network card of your PC with one of the four yellow ports on the router ("HOME NETWORK 1-4") with a patch cord. In this case, the settings for obtaining an IP address on network card should be set to 'Get automatically'. You can learn more about network settings on the ethernet interface of a PC in the help sections "Instructions for setting up a network in Windows ...":

2. Enter the router setup interface and change the default password:

To enter the router configuration interface, you need to open a browser (Internet Explorer, Mozilla Firefox, Google Chrome, Opera, etc.) and enter the address http://192.168.1.1/. The default username is admin and the password is admin. If you cannot access the web interface, or the router was previously configured for use in other conditions, we recommend that you restore the factory settings or check the network settings on the PC. The factory settings on this router are restored by pressing the hidden "reset" button for 5-10 seconds. After that, the indicators on the router will turn off and turn on again, which will mean resetting the current settings and restoring the default settings. The settings on the PC should be set to 'Receive Automatically'. You can find out how to change the network settings on the ethernet interface of a PC in the help sections "Instructions for setting up a network in Windows ...". After that, you need to click the "Web configurator" button and change the default password:

3. Setting up access to the Internet:

To configure access to the Internet in the "Internet" section (the planet icon in the bottom panel of the interface), select the "Connections" subsection, click on the "Broadband Connection" connection and enter the following data:

After that, you need to click "Apply".

4. Wireless network setup:

To set up a wireless network in the "Network-Wi-Fi" section (the Wi-Fi icon in the bottom panel of the interface), set the following parameters:

After that, you need to click "Apply".

5. Updating the firmware of the router:

The settings made are enough to access the Internet, but for more stable and high-quality work, it is recommended to update the version of the router's microcontroller. You can do this in the "System - Components" section (gear icon in the bottom panel of the interface). It is necessary to select the necessary components (the most important ones are automatically selected) and click the "Update" button.

6. Router responses to ICMP requests:

To diagnose connection quality when contacting technical support, you must allow your router to respond to ICMP requests. Go to the "Security - Firewall" section (shield icon in the bottom panel of the interface). You must click "Add Rule" and enter the following data:

These settings are enough for comfortable work on the Internet. If you have any questions, you can always contact the 24/7 technical support by phone 8-800-755-05-55.

Zyxel Keenetic Start is a light model of Zyxel Keenetic. Nevertheless, Keenetic Start will perfectly solve the problem of connecting electronic devices to the Internet. The router will allow you to combine home computers and all kinds of gadgets into a network and provide simultaneous Internet access from several devices via Wi-Fi.

For guest devices, it is possible to allocate a separate WiFi networks with Internet access, but with limited access to personal data. A regular firewall is responsible for the information security of the home network.

Complete set of the router and its appearance

The package bundle of the router is minimal: small network cable, documentation and power supply. All inscriptions on the body of the device are made in Russian. Wall mount available. In a convenient place is the WPS activation key - a function that allows you to simply and immediately connect devices to a Wi-Fi router without using an encryption key.

By appearance the router in question is very similar to its older brother (Keenetic 4GII). It only differs by the absence of USB ports and the presence of only one 2dBi antenna.

The device is quite compact (140x110x30 mm). Its weight is only 180 grams.

On the top side there is a manufacturer's trademark, a WPS key to turn on an automatic secure Wi-Fi connection, and LED indicators for power, the inclusion of a wireless Wi-Fi module, the presence of an Internet connection and a connection to lan ports.

All ports and connectors are located on the back of the router.

Connection and preparation for work

Connection Zyxel router Keenetic Start may seem complicated at first glance.

Consider the connection process in detail:


After connecting the router, it is important to configure the Zyxel Keenetic Start router. To configure it, you first need to log in to the router interface.

Login to settings

To configure and maintain the router, there is no need for specialized programs. All control of the router is carried out using a web browser.

To enter the interface of the router, you must do the following:


In Zyxel routers, there is a "Quick Setup" for the initial Internet setup.

Internet connections

The router supports several options for connecting to the Internet, which are primarily determined by the choice of a communication service provider.

PPPoE for Dom.ru, TTK and Rostelecom

The sequence of steps for setting up a router from Zyxel for these providers (Rostelecom, TTK and Dom.ru) is as follows:


An Internet connection will be created.

Dynamic IP

To set up an Internet connection with a dynamic address, you must:


An Internet connection with a dynamic IP address is ready.

Video: Zyxel Keenetic Start Review

How to set up a Zyxel Keenetic Start router for beeline

The sequence of steps for setting up the router in question for Beeline is as follows:


As a result of the actions taken, a new connection for Beeline will be created.

LAN

To set options local network on the wifi router necessary:


WiFi

The sequence of actions for setting up a Wi-Fi connection on the Zyxel Keenetic Start device is as follows:


IPTV

IPTV is a special technology that, when transferring information in networks, uses a specialized IP protocol. Thanks to this, TV channels are broadcast using multicast. For IPTV to function, you just need to install the latest firmware version of the device, and the application will automatically make the correct settings.

In the router in question, the “Applications” tab is responsible for setting up IPTV, in which you should enter the required parameters and save.

Reset router

To reset your router, follow these steps:


After that, the power indicator of the router will start flashing and then the router settings will be reset to the factory (default settings).

Updating the firmware

Quite often there are cases when it is vital to update the firmware of the device. Despite the fact that this is a very responsible action, if you follow certain instructions, it is not at all difficult to install a new version of the software yourself.

It is recommended to update the software under consideration by connecting to the router using an Ethernet cable. To update the firmware, you need to use the standard component update function. It is important that you have a stable Internet connection when performing the update.

To update the firmware on a Zyxel router, you must:


No wonder Zyxel positions Keenetic Start as an entry-level Internet center. Setting it up is very trivial, and the possibilities allow you to create a compact computer network without much difficulty. It is an ideal choice for home and compact office.

You may be interested